TEL+44 (20) 8969 1367
FAX+44 (20) 8968 8913

admin@kaloricheater.co.uk
31-33 Beethoven Street
London W10 4LJ UK

:: CATALOGUE CONTENTS
A1 compact portable
industrial fan heaters
A2 portable fan
assisted heaters
B1 4-20kW
unit heaters
B2 uht unit
heaters
C1 warm air curtains
and high level heaters
D1 mayfair
convectors
D2 forced air
consoles
D3 panel
heaters
E1 rectangular rod
type heater batteries
E2 circular rod
type heater batteries
E3 insertion
units
F1 control
panels
G1 tubular
heater units
H1 immersion
heater units
I1 electric
elements
J1 ATEX, EExd
fan assisted unit
J2 ATEX, EExd
convector heaters
J3 ATEX, EExd cabinet
convector heaters
K1 industrial finned
tubular heaters
L1 halogen
heaters
L2 ceramic
heaters
L3 weather resistant
halogen heaters
L4 halogen ceramic
and radiant heaters
M1 heating
cables
M2 heater
mats
M3 under laminate
elements
N ? other products
and enquiries
   

HOME |  PRODUCT CATALOGUE |  COMPANY PROFILE  |  ENQUIRIES

  
   

M3 | KLH
Under Laminate Elements

APPLICATION

Ultra-thin KLH heating elements can be installed directly under laminate floors without the need for screed or adhesive. They can also be used with timber floors with a maximum thickness of 15mm*. A layer of Depron insulation placed below the KLH element will provide the necessary thermal insulation and sound deadening. In poorly insulated properties supplementary heating may be required.

* We recommend you consult your timber floor supplier to check compatability with underfloor heating.

FEATURES

Two different widths are available with standard lengths up to 10m (elements can be reduced in length on site if necessary).

Non standard lengths are available on request.

4m 'live' and 'neutral' cables are fitted

A number of elements are used to fill the floor area and are connected in parallel.

KDPT programmable thermostat with both room and floor sensor (must be ordered separately).

SELECTION

Draw a plan of the floor identifying areas occupied by fixed furniture such as kitchen cabinets (heating elements should not be installed in these areas). Draw the heating elements side by side on to the plan leaving a minimum gap of 50mm between the wall and the edge of the heating element. Whenever possible, keep the elements ends fitted with the live and neutral cables along one wall. This should be the same wall on which the thermostat is mounted.

 
Specifications

KLH4 Range
Width 400mm overall, 330mm heated		 KLH5 Range
Width 530mm overall, 500mm heated
List No. Length Output List No. Length Output
m kw m kw
KLH4-010 1.0 0.04 KLH5-010 1.0 0.06
KLH4-015 1.5 0.06 KLH5-015 1.5 0.10
KLH4-020 2.0 0.09 KLH5-020 2.0 0.13
KLH4-025 2.5 0.11 KLH5-025 2.5 0.16
KLH4-030 3.0 0.13 KLH5-030 3.0 0.19
KLH4-035 3.5 0.15 KLH5-035 3.5 0.23
KLH4-040 4.0 0.17 KLH5-040 4.0 0.26
KLH4-045 4.5 0.19 KLH5-045 4.5 0.29
KLH4-050 5.0 0.21 KLH5-050 5.0 0.32
KLH4-055 5.5 0.23 KLH5-055 5.5 0.36
KLH4-060 6.0 0.26 KLH5-060 6.0 0.39
KLH4-065 6.5 0.28 KLH5-065 6.5 0.42
KLH4-070 7.0 0.30 KLH5-070 7.0 0.45
KLH4-075 7.5 0.32 KLH5-075 7.5 0.49
KLH4-080 8.0 0.34 KLH5-080 8.0 0.52
KLH4-085 8.5 0.36 KLH5-085 8.5 0.55
KLH4-090 9.0 0.39 KLH5-090 9.0 0.59
KLH4-095 9.5 0.41 KLH5-095 9.5 0.62
KLH4-100 10.0 0.43 KLH5-100 10.0 0.65

 
Depron Insulation

Dimensions (mm)
Long Wide Thick
KDEP 1200 800 6

 
Controller

Model Range Rating
KDPT +5°C to +30°C 15 amp

 

Design, specification, prices, etc. subject to alteration without notice